Accessories
from DiveLife

1/2" UNF male to 3/8" UNF female adaptor. For use when fitting standard reg hoses to the larger 1/2" UNF port found on some first stages. No suitable for the Mares MR22 1st stage...

1/2" UNF Plug...

1/2" 316 stainless steel boltsnap...

1/4" BSP Parallel blanking plug...

100mmdouble ended stainless steel boltsnap in316 stainless...

90mm stainless steel caribina...

120mm double ended stainless steel boltsnap in 316 stainless...

Stainless steel jubilee band. 120mm for 3 and 4lt cylinders...

120mm stainless steel boltsnap in 316 stainless...

160mm jubilee band in stainless stell. Fits 5 and 7lt cylinders...

200m stainless jubilee clip to fit 10 and tall 12lt steels and the new Luxfer 11.1 (S80) aluminium cylinders...

220mm stainless steel jubilee band to fit dumpy 12lt or 15lt cylinders...

25mm high quality stainless steel split ring...

3/4" 316 stainless steel boltsnap...

3/8" UNF 90 Degree elbow. Allows a 3/8" UNF hose to exit a 1st stage at 90 degrees to ease hose routing...

3/8" UNF Male to 1/2" UNF Female adaptor. Used for fitting 1/2" UNF reg hoses to standard 3/8" UNF reg port...

3/8" UNF Blanking Plug...

The 3/8" male x female adaptor allows for a Miflex hose to be used with and Inspiration or Evolution rebreather and the hoses to seat correctly on the manifold, due to the clean shoulder on the adaptor....

3mm bungee cord per metre...

4mm stainless stell threaded quick link...

50mm stainless steel caribina...

6mm bungee cord - per metre...

6mm stainless steel threaded quicklink...

7/16" 90 Degree elbow. Allows easier routing of high pressure hoses when leaving the first stage. Can also be used to fit a computer transmitter to first stages such as Poseidon...

70mm stainless steel caribina...

90mm stainless steel boltsnap...

Polished stainless steel billy rings available in eith 45 degree or 90 degree versions...

AP Flow-Stop The Flow-Stop is an in-line gas isolator. Simply slide the black knurled collar forwards in the direction of the gas flow to instantly cut off the gas supply. The Flow-Stop features large bore feed holes that are recessed to reduce o-ring wear. The high-flow design o...

Compressor charging adaptor. Essential when travelling (Screws into DIN fitting cylinder outlets and allows filling from compressors fitted with A-Clamp....

BK31 - Verti-clip Holds an AP27 BUDDY 50mm stainless D-ring vertical on any area of 50mm webbing Allows easy one-handed attachment of trigger hooks or karabiners(D-ring shown not included)...

Apeks AP0195 din to yoke clamp adaptor. Simply screws onto a din fitting to convert to a-clamp. No tools needed....

Apeks AP 0211 300 bar din convertor. Used to convert Apeks regulators from A-Clamp to DIN...

Over pressure valve for suit inflation system. Screws straight into a standard 3/8UNF low pressure port. Fits all new regulators in the UK...

Includes necessary attachment hardware plus spares. May be used without the SureLock™ Weight System to spread the weight of the cylinders over the hips 3 different grommets settings allow for proper positioning of the SureLock™ weight pockets. RRP £30.80 now only £26...

Bolts directly to the WTX Harness Able to mount to the back plate with use of SureLock attachments Includes necessary attachment hardware plus spares. 2" stainless adjustable D-rings on the outside of each pocket. Features the SureLock (patent pending) mechanical weight release buckles. Preven...

AQUA.GREASE HIGH QUALITY Click Here for larger image SILICONE GREASE BLISTER CARD INSTRUCTIONS ON BACK CONTENTS 1 X 35 GM TUBE AQUA.GREASE USES. For servicing Aqua/Scuba regulators, pillar valves, ‘O’ Rings, camera parts, threads, outboard e...

Easy D Ring attachments to BCD or jacket webbing. 50mm 45° Single Welded D - 45D50mm 90° Single Welded D - 90D...

Divers are always running out of space to carry things. The New BF Backpacker is the answer to this, making use of the space at the side of the cylinder. Ideal for carrying those more bulky items that may be used only once during the dive, for example the JR Delayed SMB or lifting bag. Suitable for ...

JR Hip Hung Tool Pouch There are never enough pockets !!This very popular tool pouch straps to the leg, and clips to your jacket or though the weight belt. The pouch expands at the sides making a large capacity pocket.Specification9oz nylon, heavy-duty pouch, with loop attachment to weight belt, or...

This pouch has been designed to aid technical divers who carry redundant masks. The JR Spare Mask Pouch clips or slides onto a strap or belt to provide easy storage and access. Although primarily designed as a mask pouch, this handy size pouch with expanding sides can be utilised to carry any other ...

Easy D Ring attachments to BCD or jacket webbing. 25mm Triple Welded D - 3D2550mm Triple Welded D - 3D50...

JR Utility Pouch Double pocket pouch designed for mounting horizontally on 50mm webbing straps or clipping to stab jacket/harness.Compact size (240 x 150mm)Zips, including slider made from 100% nylonManufactured in heavy duty CorduraConvenient for accommodating redundant mask, tables, slate, buddy ...

Cord with cord lock and size 0 snap hook....

Allows charging of valaves fitting the DIN 300 Bar connector by compressors with A-clamp fitting hoses....

Quickly converts 232 Bar DIN fitting charging hoses for instant use with 232 Bar A-clamp cylinder valves....

Converts 232 Bar DIN outlet to 300 Bar DIN inlet, allowing the connection of 300 Bar cylinder valve to a 232 bar compressor hose. 232 Bar Female/300 Bar DIN Male  -  AD 2D3D    232 Bar Female/300 Bar M26 Male -  AD 2D63F    ...

A-Clamp and 232 BAR DIN outlet. Used to filter air between compressor and cylinder. Reduces possible cylinder contamination from air fills ensuring a lomg cylinder life, may be used with DIN to A-clamp adapter....

Two size 1 snap hooks on 3 metres of high visibilty 25mm webbing....

Usewd to filter air between compressor and cylinder with 300 BAR DIN type attachments. Reduces cylinder contamination, ensuring a long cylinder life....

Simply adapts 300 Bar Din fitting charging hoses for instant use with 232 Bar A-clamp cylinder valves....

Converts single 232 Bar A-clamp outlet to two 232 Bar A-clamp outlets. Allowing the use of two A-clamp fitted regulators from one air source....

Converts single 232 Bar A-clamp outlet to two 232 Bar DIN outlets. Allowing the use of two DIN fitting regulators from a single air supply....

Heavy duty 50mm nylon cam band with industrial velcro and a quick release stainless steel buckle. Can be fitted to most types of cylinder and jackets to allow quick and easy changing of cylinders. Secures single cylinder  up to 15 litres to B.C.D or backplate....

Complete swervicing kit for routine maintainance of Personal Air filters. To be used after 1 year or 100 fills, contains activated charcoal, O-rings and filters....

AIR INFLATION GUN Stainless steel air inflation gun with push button trigger. Integrated split ring and fast action attachment clip. Fits regular QD coupling BCD hose, used to inflate lifting bags, etc. AIR INFLATION GUN...

AIR INFLATION NOZZLE NOZ Attaches to standard QD fitting BCD hose to inflate lifting bags and other equipment from air cylinder. Complete with split ring and rust free attachment clip. AIR INFLATION NOZZLE...

...

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

High performance, sturdy replacement inflation unit, fits all Beaver and Tigullio jackets and most other standard brands. BCD INFLATION UNIT...

Replacement corrugated hose assembly, including optional pull cord for inflation/exhaust where fitted. Fits most styles of jackets....

Quick release hose for use with most BCD inflators. One 3/8" UNF male thread and standard QD fitting to the inflator. Complete with fitted hose protector for extended durability....

High quality stainless steel 90° or 45° static billr ring for fixing to webbing. For simple attachment of side mount stage cylinders and other equipment....

Extremely strong, highly flexible cable line with rust resistant stainless steel carabiner clips for high security & fast action release. Extending to around 75cm when fully deployed. Used to attach accessories stowed then conveniently accessed when required....

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

Crystal silicone, ergonomic design for extreme comfort. Fits most regulators and snorkels with seperate mouthpieces, supplied with convenient tie wrap fastener included for imediate use. Colours: Black and Clear....

Cord with small cord lock and rubber wrist band for added comfort....

Dive Slate with Explorer Compass and precision tipped dive pencil on flexible elastic cord & mini sea coil self retracting wire with quick release attachment clip for ease of use underwater. Ideal for noting way points....

Heavy duty nylon cord laocks rust free. Use with lanyards or cord for quick adjustments. Sold in Pairs. Small - COR S  - £1.60 Large - COR L  - £2.25 ...

28b of Flouro-Ultra 02 grease in a handy syringe for accurate no waste application. For use when servicing cylinder valves and regulators that are O2 clean for Nitrox....

Converts single 232 Bar DIN outlet to two 232 Bar DIN outlets. Allowing the attachment of two DIN fitting regulators from a single air source....

Key Ring in the shape of a diving helmet. Made from high quality Brass....

Large, 175mm x 125mm slate with two pages and a precision tippd dive pencil on flexible elastic cord & resilient quick release attachment clip for ease of use underwater. Giving you maximum space for your underwater use or communicating with your buddy or trainee....

2 metre long adjustable line made from 25mm marine grade webbing with stainless steel drift hook in a durable nylon pouch. Pouch features velcro closure and intergral nylon D-ring....

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

Convenient sized 10ml bottle of hyperallergenic Earol spray. For use before swimming to prevent the unpleasant symptons & potentially harmful effects of trapped water in the ears. Reduces the risk of ear infection. Supplied in a handy pastic box for storage....

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

Conveniently sized fin shaped key ring. Stainless steel split ring for attachment of keys etc. Available in blue only...

For use with most popular types of high pressure gauges and consoles, complete with NITROX compatible O-rings....

Allows connection of several low pressure hoses to a single outlet. Ideal for technical divers with many accessories.  3/8" UNF Triple outlet   AD 3T      3/8" UNF Double outlet   AD 3D      3/8" UNF 90° Single outlet...

High quality stainless steel adaptors allow conversion of a variety of thread types, allowing connection of Beaver hoses to almost any regulator.  1/2" Male to 3/8" Female  AD 1M3F  3/8" Male to 1/2" Female  AD 3M1F  3/8" Male to 7/16" Female  AD 3M7...

With swivel, for secure attachment of gauge & octopus to B.C.D or Harness....

Compact stainless steel swivel unit allowing improved freedom of movement and comfort. For use with most regulator and octopus hoses....

2.3 metre long line made from 25mm heavy duty webbing with stainless steel hook fo attachment to the shot line. Comes in convenient nylon storage pouch with integral belt loops for attatchment to harness or BCD....

Large, A4 sized slate with precision tipped dive pencil on flexible cord and resilient quick release attachment clip for ease of use underwater. Allowing extra space for your underwater use or communicating with your dive buddies....

5mm heavy duty cord with large cord lock....

Extra strong 5mm cord with cord lock and size 3 snap hook....

5mm heavy duty cord with cord lock and large split ring....

Allows attachment of M26 Bar Regulator to a DIN valved Cylinder. 232 Bar M26 Female/232 Bar DIN Male  - AD 62F2D     232 Bar M26 Female/300 Bar DIN Male  - AD 62F3D      300 Bar M26 Female/300 Bar DIN Male  - AD 63F3D     ...

With nylon side release buckle and small split ring for safe Octopus attachment....

Handy standard length Octopus hose with useful integrated air gun. A great tool for regs with limited low pressure ports....

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

For use to isolate aregulator 2nd stage in the event of free flow especially on regulators not designed fro use in cold waters. By fitting the HS SOV a simple yet effective sliding action of the sleeve will manually isolate the free flowing regulator or octopus, allowing for  a safe ascent. S...

Pair of high grade stainless steel removable D-rings. Enables fst efficient attachment of most accessories to B.C.D. or harness. 38mm  -  DRI R3  -  £8.40 50mm  -  DRI R5  -  £10.80 ...

Handy lightweight aluminium key ring and bottle opener in the shape of a shark. Stainless steel split ring for attachment of keys etc....

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

Pair of dive slate pencls designed for underwater use. May be used as a replacement for virtually all models of dive slate. ...

3mm cord with cord lock and small split ring....

61cm long 25mm wide webbing with size 2 bronze snap hook on one end and 51mm split ring on the other....

Strong elasticated cord with 25mm webbing and size 1 snap hook with swivel....

Stainless Steel Key-Ring type split rings. Supplied in pairs. Small 38mm  -  SPR S  -  £1.60 Large  51mm  -  SPR L  -  £1.99 ...

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

Beaver Mulit-clips 25mm wide durable webbing with a variety of useful fittings for attaching your diving accessories, allowing quick convenient access when needed. Rust resistant snap hook, male and female buckles, stainless split rings, elastic hoops, lanyards and D-rings are all featured creatin...

300mm long stainless steel pointer with engraved graduations. Ideal for use when instructing students or giving guided underwater tours, can also be used for aproximating measurements for smaller items. Comes comlete with coil spring line and nylon attachment clip enabling safe and secure attachment...

A handy combination of scuba rattle and 8 inch graduated pointer to attract the attention of other divers and then point to wildlife and other interesting undeerwater features. Comes complete with comfort wrist lanyard for ease of use and security while diving....

Extending to approximately 75cm with rust resistant 316 stainless steel cable line with snap hook fittings. Ideal for secure attachment of accessories allowing quick and convenient access when required....

Conveniently sized A5 multi use dive slate with pencil on elastic cord and quick release attachment clip for ease of use. Extremely durable shatterproof corrosion free materials. Size: 15cm x 13cm...

61cm of 25 mm webbing with size 1 and 2 snap hooks with swivel and cord attachment loop....

Cord with 25mm webbing and size 1 snap hook with swivel for torches slates etc....

TYRE INFLATOR TYR Attaches to most standard BCD hoses with QD coupling to easily inflate tyres, boats, etc. with Schraeder type valve from a cylinder with first stage regulator....

Pack of 6 Silicone rubber 240mm Long Uni-Ties. Highly versatile ties for use in many situations when securing light items of equipment for quick release and immediate use. Easily combines together to increase length. Colour: Black...

Replacement note book insert for wet notes wallet, double front cover to protect your paper contains 30 sheets. Suitable for most leading Wet Notes style note book wallets. Page Size: app.17 x 10cm...

A handy cordulon wallet containing 30 sheets of waterproof paper for use making detailed notes and drawings while diving. Supplied with a Beaver slate pencil on an elastic cord & D-ring attachment point. Page Size: app.17 x 10cm...

Ergonomic dive slate with three opening pages to allow storage of a multitude of information. Includes pencil on elastic cord and attachment point. Designed to fit comfortably on the wrist over wet or dry suit...

A 2 pocketed zipped pouch that can be threaded onto 50mm webbing. Both zips have toggles attached for easy opening. A plastic slide is attached on the reverse to prevent the bag moving around. Size: 24cm x 17cm x 6cm...

316 Stainless Steel...

A 12 Battery Pouch & Lampholder  ...

Accessories Pouch --------------- This spacious pouch will slide onto 50mm webbing and has a large velcroed flap. Size 22cms x 23cms x 8cms....

A traditional 'D' Ring angled at 45 degrees with two bars to seperate 3 colums were webbing can be threaded through....

The ideal pouch to carry a reel and S.M.B.A snap bolt at the top to attach to a “D” ring and a strap to fasten around the leg.Size 28cms x17cms x 11cms....

25mm Slide release buckle with a stainless steel slplit ring on each end...

This packet contains a pouch to carry the battery pack, 1 strap to go around the bottle and an elasticised holder on a quick pull Velcro tab....

Goody Bag Pouch --------------- A simple pouch that will slide onto 50mm webbing, designed to carry a Bowstone goody bag. Velcro fastening on flap. Size: 20cm x 8cm x 8cm...

Designed to take the Green Froce or similar sized torches....

A 3mm neoprene wrapover with a Velcro fastening. Ideal for wrapping around a convoluted hose...

Joey Pouch --------------- This pouch will fit across most B.C.s and with a permanent secure point to one side, and a snap bolt to the other a quick kit down will be easily achieved. A divider is inside the pouch and a Velcro flap. Size 20cms x 25cms x 9cms....

Leg Pouch --------------- With a snap bolt at the top of this pouch, it can be easily attached to a "D" ring, and the strap at the base fastened around the leg. A Velcro flap and 2 drain holes complete this very popular pouch. Size: 30cms x 18cms x 6cms....

Mask Pouch --------------- An ample sized pouch to carry a spare mask or similar and will slide onto 50mm webbing. Velcro fastening on flap. Size: 19cm x 13cm x 7cm...

Mask Pouch --------------- An ample sized pouch to carry a spare mask or similar and will slide onto 50mm webbing. Velcro fastening on flap. Size: 19cm x 13cm x 7cm...

A neoprene panel with Velcro tabs either side to attach to your mask...

Simply thread your mask strap through this cover to give a more comfortable feel....

Will slide onto 50mm webbing. Has a 2-way zip on the top, and two eyelet drainholes on the bottom of the pouch. Includes a velcro fastened pouch attatched to the front for extra storage, ideal for a goody bag or SMB.Size: 19cm x 18cm x 8cm...

Will slide onto 50mm webbing. 2-way zip on the top of the pouch, with two eyelet drainholes on the bottom. Four eyelets on the front for bungee-cord to be tied to. Ideal for holding a goody bag, SMB etc.Size: 20cm x 19cm x 8cm...

25mm slide release buckle with webbing on one end. 2 cable ties to attach the other end to wherever you like.....

25mm Slide release buckle with webbing loops on both sides....

25mm Slide release buckle with webbing on one end and a stainless steel split ring on the other....

Spare Reg Pouch --------------- Designed to carry a second stage, and can be attached, by a webbing loop, around the neck of the bottle. With a Velcro flap this bag will keep your reg right where you want it until you need it...

Spare Reg Pouch --------------- Designed to carry a second stage, and can be attached, by a webbing loop, around the neck of the bottle. With a Velcro flap this bag will keep your reg right where you want it until you need it...

When not in use, this pouch can be folded up and held secure with a stainless steel stud. Will thread on to 50mm webbing. It has two drain holes at the bottom. Velcro fastening.Size: 20cm x 30cm, 20 x 12cm (rolled up)....

A 3mm neoprene wrapover with a Velcro fastening. Can easily be wrapped around your shoulder straps for added comfort....

A 2 or 3 pocketed, arm mounted slate holder. The diver can carry, and easily view more than one table or run time. Elasticated straps and Velcro fastening on pockets. Inside pocket size 10cms x 14cms...

A simple pouch that will slide onto 50mm webbing, designed to carry a rolled up Bowstone S.M.B.Velcro fastening on flap. Size: 18cm x 7cm x 7cm...

Nickel plated bronze...

316 Stainless Steel...

Suit Pocket --------------- A heavy duty textured nylon pocket, attached to a neoprene back, which can be glued to most suits. With a velcroed flap and eyelets for drain holes. Size: 27cm x 20cm x 7cm...

Good sized pouch with a D ring sewn inside, a zipped opening and a velcro front pocket for extra storage. Will slide onto 50mm webbing. Size 24cm x 24cm x 9cm....

Good sized pouch with a D ring sewn inside, a zipped opening and a velcro front pocket for extra storage. Will slide onto 50mm webbing. Size 24cm x 24cm x 9cm. Complete with a pair of stainless steel scissors in a pouch, sewn to the font....

Utlity pouch --------------- A 2 pocket zipped pouch that can thread onto 50mm webbing or fit over an elasticised cumberband on a B.C. Size 23cms x 15cms x 5cms....

Cargo Pouch --------------- The strap on this pouch will thread onto 50mm webbing, and can easily be removed by releasing the large slide release buckle.2 long straps can be fastened around the leg. Size: 25cm x 17cm x 10cm....

A 2 pocket pouch, one pocket with a zip fastening, the other with a Velcro fastening.There are 2 drain holes on the bottom. The pouch will thread on to 50mm webbingSize 26cm x 16cm x 7cm...

Zipped cargo pouch --------------- The strap on this pouch will thread onto 50mm webbing, and can easily be removed by releasing the large slide release buckle.2 long straps can be fastened around the leg. The zip has a toggle attached for easy opening. Size: 25cm x 17cm x 10cm....

A 3mm neoprene zipped pocket, with a toggle attached to the zip for easy opening. Can be glued to most suits....

Bowstyone zipped suit pocket...

Diver buddy line RRP £10...

Weight system for the new Buddy Tekwing...

Bungee Lanyard...

Bungee Whistle Lanyard (whistle not included)...

Coiled lanyard with 25mm split rings on each end...

Console Detach Lanyard ...

Cressi AnitFog spray...

Cressi Fin Strap. Fits all Cressi fins with open heel. Fins not included...

Pair of buckles to fin either the Cressi Frog or Pro Light fins...

Pair of buckles to fit either the Cressi Rondine A or new Reaction fins...

Curly Wurly Lanyard...

Backpad for Custom Divers backplates...

Custom Divers bump bag...

Custom Divers hose wrap sleeve...

Quick Fit Weight Pocket The Quick Fit Weight Pocket is easy to fit to add weight for all requirements by attaching to Wings/BCD Systems and trimming equipment without fuss. The pocket has a maximum capacity weight of 2kgs block lead or shot.The system comprises of two pockets flaps which are secu...

Those of you who have never come across the SeaCURE Custom Mouthpiece will be pleased to hear it does have pedigree. It was scientifically designed by Orthodontist, Dr Randall Moles in 1992. His aim was to create a mouldable mouthpiece that each diver could easily self mould to correctly fit their m...

Pair of Custom Divers shoulder covers...

An adaptor to connect from a Poseidon Cyklon 2nd stage to a standard 9/16" regulator hoseExclusive to Miflex Hoses...

Detach camera lanyard...

Detach Coiled Lanyard (IMPROVED! NOW WITH EXTRA KEY RING)Coiled Detach lanyard stretches to 36 inches. Incorporating fastex buckle on webbing with cord loop for attachment. Fitted with No 1 Swivel Eye Nickel Plated Bronze Snap Hook OR 90 mm Bronze Bolt Snap. ...

Detach SMB Reel Lanyard...

Detach Torch Lanyard...

Detach Lanyard with srewgate...

Single DIRZone cam band with stainless buckle Picture for example only, only one single cam band is included in the purchase...

DIRZone standard bellows pocket...

DIRZone wetnotes. Ideal for underwater writing...

Dive Rite 16lb Weight Pocket System Tall and narrow, these weight pockets leave plenty of room on the waist belt for other accessories. This set of right and left hand pockets include a pocket insert that holds the lead and a separate weight pocket holster. Set at an angle so divers can easily slip ...

Dive Rite 32lb Weight Pocket System Hefty weight pockets hold plenty of weight for cold water divers. This set of right and left hand pockets include a pocket insert that holds the lead and a separate weight pocket holster. Set at an angle so divers can easily slip the pocket into the holster with o...

Dive Rite Bellows Horizontal Pocket w/Daisy Chain Internal depth expands from 0.5” to 2.5”6”x10”x2.5” Weight: 4 oz/113 grams...

Dive Rite Bellows Velcro Pocket w/Daisy Chain Internal depth expands from 0.5” to 2.5”10”x6”x2.5”Weight: 4.4 oz/125 grams ...

Dive Rite Bellows Zip Pocket w/Daisy Chain Internal depth expands from 0.5” to 2.5”10”x6”x2.5”Weight: 3.8 oz/108 grams...

Dive Rite Clipper Pocket 1680 denier ballistic nylon fabric is tear & abrasion resistant. Two-inch nylon webbing loops on the back of the pocket slide over a standard 2” webbing waist strap and secure the pocket into place. Heavy duty Velcro secures pocket flap and resists sagging and stre...

Dive Rite D-Ring Holder Kit ...

Dive Rite Executive Slate 6 Leaf erasable slate pages. Graphite stick pencil included 13 x 10cm....

Fits up to 4.38inch, 5.25" or 8" cylinders...

Dive Rite D-Ring Holder kit ...

Dive Rite Notebook Cover Organiser w/ Dive wRites It is a tri-fold wallet that closes with Velcro. Made of ballistic nylon, it has storage for three pen/pencils with elastic keepers and has pockets in the back flap for storing C-cards, insurance card or any other similar sized items. The Notebook co...

Dive Rite O2 Second Stage Pocket 1680 denier ballistic nylon fabric is tear & abrasion resistant. Stainless steel, 1” D-ring on the back of the pocket is used to clip into an oxygen deco bottle stage strap.Two-inch nylon webbing loops on the back of the pocket slide over a standard 2&rdquo...

Dive Rite Stainless Large Clamp Band ...

Dive Rite Stainless Small Clamp Band ...

Dive Rite Thigh Pocket w/Daisy Chain Proprietary fabric leg band is 4” in width with silicone strips that grip the exposure suit and prevent slippingInternal depth expands from 0.5” to 2.5”10”x6”x2”Weight: 7.2 oz/204 grams...

Dive Rite wRites Waterproof Notebook 45 erasable pages Graphite stick pencil included 12 x 17cm....

With split ring and plastic snap hook for attachment of octopus. Ensures your regulator is in the correct position and reduces contamination...

Diver's Neck Lanyard...

Divers A5 slate RRP £9.50...

Diver's Wrist Lanyard...

These domed nuts replace the wingnuts found on twinsets. They are marine grade stainless and are drilled and tapped with a standard 8mm centre...

Regulators not designed for cold water use are especially prone to freezing. Our simple yet extremely effective Freeflow Control Device contributes a significant advance in diver safety. In the event of 2nd stage freezing, freeflow can cause catastrophic loss of air. With the FCD fitted to your r...

BENEFITSPerfect for travel, complete with rollout inside. Ideal for SMB storage or when you might be using a wet or dry suit without thigh pockets MATERIALS1680 Denier Nylon. YKK zipper FEATURESSlides onto the Secure Harness strap; rigid ABS-reinforced plate holds pocket shape during dive. Pocket ...

General purpose detahc lanyard...

The bellowed pocket features a streamlined, tapered sidewall design that still allows ease of use with dry gloves or mittens. It also has two tough braded nylon loops with enough room to clip off a spools and accessories. Two large grommets along the bottom of the pocket allow for quick draining....

Halcyon’s high quality neoprene mask strap fits any standard mask attachment, and provides an extra degree of comfort and stability....

Halcyon mask strap cover. Fits most masks...

Simple attachment necklace for your reserve second stage. Thin enough to fit under your mouthpiece zip-tie, strong enough to last several dive seasons. We like to think of it as another example of DIR's zen elegance when compaired to other contraptions used to secure your back-up regulator....

Halcyon right hand zippered pocket for attaching to harness strap...

Yet another tool that allows you to get weight off your weight belt, the Halcyon Weighted Single Tank Adapter provides six pounds of non-releasable ballast between you and your single cylinder rig. The Weighted STA works with all Halcyon backplate designs. The Weighted STA is pictured above on the l...

Halcyon stainless steel fin spring straps for jetfin style fins. Avaiable in med (82), large (10") or extra large (12")...

Halcyon pockets add a critical level of functionality to your wet or dry suit, allowing readily accessible storage of utility and emergency items. Our heavy-duty pockets provide plenty of room for your spare Halcyon mask, your Stainless Steel bolt snaps, your favorite Defender spools, or any dive ac...

Replacement paper refill for the Halcyon Diver's Notebook....

Even the most casual of diver will appreciate the advantages of an underwater notebook over a plastic slate. Photographers have more room to make notes about locations and exposure settings, wreck divers more room for details about their discoveries. Sized to fit in any BC or suit pocket, Halcyo...

Hammerhead ACO snap clip on keyring...

Force 24oz Extension 32"...

Snap clip or bracket mount. 12 oz force, 42" extension...

Snap clip or bracket mount. 24 oz force, 32" extension...

Force 9oz Extension 31"...

Clip mount. 3 oz force,36" extension...

Heavy duty 3 bar stainless steel slide...

Heavy duty detail coiled lanyard....

Heavy Duty Detach Coiled Lanyard - No.3 Snaphook Coiled Detach lanyard stretches to 36 inches. Incorporating large, heavy duty fastex buckle for easy use with gloved hand. ...

Heavy Duty Detach Coiled Lanyard - 115mm Boltsnap   Coiled Detach lanyard stretches to 36 inches. Incorporating large, heavy duty fastex buckle for easy use with gloved hand. ...

Heavy Duty Detach Coiled Lanyard - 115mm Boltsnap and 4mm Delta Quick Link Coiled Detach lanyard stretches to 36 inches. Incorporating large, heavy duty fastex buckle for easy use with gloved hand. ...

Heavy Duty Torch Lanyard Number 3 snap hook on webbing with 7 1/2" cord loop ...

Use to mount a Mini Gauge to a HP hose. Right angle (90 degree) with the HP hose. Air spool with viton O-rings included. Oxygen cleaned. ...

Use to mount a Mini Gauge to a HP hose. Inline (180 degrees) with the HP hose. Air spool with Viton O-rings included. Oxygen cleaned. ...

Can be installed on any 2nd stage and allows instant stopage of airflow through hoseProvides complete protection from an octopus free flow while divingIdeal for decompression bottles or stage bottles where preventing gas loss is critical ...

Required swivel between HP hose and SPGBrass construction Oxygen compatible with viton o-rings Available with shoulder or bullet type. ...

Decompression Arm Slate with pre-printed grid...

Multi-Purpose IANTD Pouch with waterproof notebook...

The hook is made from high tensile 304 stainless steel 5mm thick and is sewn to strong nylon webbing 1" wide and 2.1m/7ft long and is attatched to a storage pouch, which has a loop to fit any 2" webbing....

The strong 1" wide nylon webbing is 2.1m/7ft long & is attached to a storage pouch, which has a loop to fit any 2" webbing. The 4mm thick, high tensile 304 S/S hook is sewn on the other end....

Made from type 304 stainless steel, the single tank adaptor is strong and has excellent anti-corrosion characteristic It has 2 sets of tank strap slots for a secure fitting. The square holes are 11 inches apart and can be easily attached to the backplate. Comes with 2 sets of attachment bolts, wash...

For stopping and stabilising oneself during a drift dive. Comes with 304 grade stainless steel single and double hooks, giving the option of using either or both hooks during a dive and an aluminium carabiner for quick and easy attachment. Each hook is tied to a sturdy 6mm, rope and is length adjus...

Designed to hold up to 4kg (8.8lb) The weight pocket is made from durable 1680 denier ballistic nylon & the highest grade of velcro & corrosion resistant zips are used as the pocket closure. It can be attached to the harness through their 2" webbing loops. Sold singly...

Designed to hold up to 7kg (15.4lb) per pocket The weight pockets are made from durable 1680 denier ballistic nylon & the hightest grade of velcro & corrosion resistant zips are used as the pocket closure. They can be attached to the harness through their 2" webbing loops. Sold singly...

Jon Line. Ideal for long decompression stops RRP £17.50...

Knife Strap ...

Large computer wrist slate RRP £10...

Large Detach Lanyard...

Large Lanyard...

Large Torch Lanyard ...

Octoquick Emergency Quick Release Octopus Holder No Squeeze ! 10lbs Positive Pull. Easy Entry Sold ready-to-use in two parts. RRP £9.99...

Din 300 Female to Male Euro Bullnose...

Male Octopus Lanyard ...

Manta regulator necklace Keep your alternative air source where you need it. A must have for advanced divers. ONE piece moulded design. Durable, no memory silicon materials. One size fits all....

Manta regulator necklace Keep your alternative air source where you need it. A must have for advanced divers. ONE piece moulded design. Durable, no memory silicon materials. One size fits all....

The legendary Aquasure flexible sealant and emergency repair adhesive. 28.4 gramme tube. Ideal for most watersport uses....

Aquasure flexible sealant and repair adhesive. Economic 240 gramme tube for regular use, ideal for repair centres....

Aquasure flexible sealant and repair adhesive. Handy twin 7 gramme tubes. Ideal for emergency use in your travelling repair kit....

Cleans and conditions all parts of your BCD, removing harmful bacteria, salt deposits and other harmful residue, ensuring a long life and great long lasting appearance, supplied in a 237ml bottle....

Precleaner and cure accellerator for Aquasure. Speeds tack time to 15 minutes and full cure time to less than 2 hours.   15ml only available...

The McNett- Jellycard has been developed on co-operation with scientists, biologists and medical experts specialising in the treatment of venomous bites and stings. The Jellycard is a one time use first aid product, specially designed to quickly limit and relieve the pain and is also an effective re...

60ml bottle of obour eliminator ideal for wetsuits and drysuits, BCDs and all types of outdoor equipment and clothing....

Advanced mask pre-cleaner and slate cleaner. Handy sized 37ml bottle to prepare new masks and clean slates, etc. before use without scratching or abrasion....

Anti-fog and lens cleaner. The built in brush applicator (60ml only) allows thorough application to all types of lenses. Suitable for use on all dive masks, goggles and optical lenses to eliminate fogging....

Anti-fog gel in concentrated extra strength formula. Use regularly for a crystal clear view. 37ml conveniently sized bottle....

A high performance anti-fog formula in a convenient sized 56ml pump spray, ideal for masks, goggles and all other optical equipment....

37ml bottle. Use regularly to dramatically increase the life of latex and neoprene seals, as well as other rubber products....

Ideal adhesive and repair sealant for nylon products such as membrane suits, drycags, etc. 28.4 gramme tube....

Handy 7.1 gramme pack with chain. For use to condition and lubricate all O-rings, etc. extending their useful life and providing a better seal....

Lubricates, conditions and protects all rubber products from salt water corrosion. Large 237ml bottle with pump action dispenser....

Regular use will keep all neoprene products in pristine condition with this economy sized 237ml bottle. Removes chlorine, salt and also helps keep most unpleasant odours at bay....

Lubricates, cleans and protects all types of zips used in water. Economy 60ml bottle with handy brush applicator to dramatically prolong the life of all zip fasteners....

Prolongs the life of all zip fasteners, as well as a host of other applications. 21.3 gramme stick of lubricating wax in a conveniently styles re-sealable protective tube....

Solid zipper lubricant to minimise rust and corrosion by lubricating all types of zip fasteners. 14.2 gramme stick in applicator. For best results, pre-clean with McNETT Zip Care....

DOuble hose retainign clip for  Miflex Xstreme & Xstreme-hi hoses. Enables Miflex hoses to be securely retained and if required fixed to each other for safe retention....

Two zipper pockets with toggles on zips,ideal for slates and back up equipment such as Jon lines, torches etc. --------------- Description Two zipper pockets with toggles on zips,ideal for slates and back up equipment such as Jon lines, torches etc. Features 11x8 inch, stiffened heavy dut...

Single tank adapter so the wing back plate and harness will go on a single cylinder ideal for the secound dive of the day or holiday diving. --------------- Aircraft grade Aluminium Description Aircraft Grade Aluminium Features Side slots can be optionally used with webbing to ad...

A pouch that secures an argon bottle to the side or base of a back plate --------------- Description An argon pouch that allows a 1.5 cylinder to be fixed to the underneath of a back plate. The pouch also protects the cylinder from knocks and scratches and allows a diver easy access to t...

This pouch pads the backplate for comfort. --------------- Description This pouch pads the backplate for comfort and secures an emergency SMB or lifting bag. Comes with plastic backplate clips. Features The pouch pads the back plate and not only provides comfort on the divers back hel...

Back plate side pockets ideal for easy storage of lift bags SMB''''s etc --------------- Description Back plate side pockets to be attached to the side of the back plate for easy storage and accessibility of lift bags SMB''''''''s etc Features Each side pocket is 11 1/2 inch long and ...

Back plate tail Ideal for storing liftbags or DSMB --------------- Description This tail has attched 2 side pockets useful for storage of spare mask and goody bag. Has 12 brass eyelets for securing deco boys and lifting bags etc. Features Plastic fastenings mean this tail can be at...

Hi visability safety flag that is only 13 inch by 4 inch when folded When expanded the flag is 78 inch in length --------------- Description Safety flag so that divers can be easily located by boats this flag is easily adjustable and a must for boat diving were there is currents or hi sw...

The Nas backplate. --------------- The Nas backplate is specially designed to take the custom made Nas harness with its quick release system. Description Back plate is laser cut and then countersunk and de-burred Features Highly polished to leave a shining finish Comes With Adddi...

This pouch is ideal for the front of harness system for a means of carrying a collection of useful tools --------------- Description This pouch is ideal for the front of harness system for a means of carrying a collection of useful tools Features 9x9 inch Velcro fastening with removab...

Tool pouch with net cutting scissors --------------- Description Tool pouch with net cutting scissors Features The pouch comes with heavy duty stainless steel trauma shears attached with a large easily accessible handle. Fitted with a 1 inch webbing securing strap and stainless steel ...

Two pocket pouch with net cutting scissors --------------- Description Two pocket pouch with net cutting scissors Features 11x8 inch, Two zipper pockets with toggles on zips, stiffened heavy duty polypropylene material so it does not crunch up when on the harness, ideal for slat...

Mount your instrument console, light or other accessory to your Oceanic BC, with our specially designed Retractor to keep it comfortably within reach. Pull the item out to use and let the Retractor pull it back out of your way. ...

The swivel ensures that the second stage is always in the required position. No twisting of the hose is necessary. It rotates through 360 degrees vertically and horizontally. RRP £20 now only £17...

1/4" NPT Male to 3/8" - 24 Male HP Adaptor...

This adaptor is a simple male to female adaptor to convert a standard 3/8" (male end) regulator hose to 1/4" NPTOne use for this is to connect a standared regulator hose to a Swagelok NPT adaptor....

This adaptor is a simple male to male adaptor to convert a standard regulator hose to 1/4" NPTOne use for this is to connect a standared regulator hose to a Swagelok NPT adaptor.Popular for use with rebreather divers, as it offers the ability to interchange hoses....

1/8" NPT Female to 7/16" - 20 Male HP Adaptor...

...

1st Stage regulator high pressure pivot swivel L-Shaped3/8" - 24 male x 3/8" - 24 Female360 degree rotation...

Quick Disconnect for 2nd stage or rebreather BOV9/16" Female thread on a nipple9/16" Male thread on a locking QD slider to screw onto a standard LP regulator hoseLocking mechanism to avoid accidential disconnection...

An adaptor to enable a standard regulator hose to be converted into a 3/8" male x male hose, complete with a union joint (the nut on the regulator hose). A simple useful adaptor for rebreather divers....

Second Stage Elbow Swivel9/16" - 18 male to 9/16" FemaleCaptured O Rings for safer swivel...

Second Stage Elbow Swivel9/16" - 18 male to 9/16" FemaleCaptured O Rongs for safer swivel...

This adaptor enables a standard regulator hose to the longer thread of an Atomic B2 type regularo - using this adaptor as a spacer nut....

Converts an AGA mask to a standard scuba hose fitting.3 way 360 degree rotationAGA 2nd stage regaulator to standard LP scuba 9/16" - 18 maleAccepts in-line quick disconnect...

Converts a Poseidon Cyklon to a standard scuba hose fitting.3 way 360 degree rotationCyklon 2nd stage regaulator to standard LP scuba 9/16" - 18 maleAccepts in-line quick disconnect...

Converts a Poseidon Xstream to a standard scuba hose fitting.3 way 360 degree rotationXstream 2nd stage regaulator to standard LP scuba 9/16" - 18 maleAccepts in-line quick disconnect...

Standard 9/16" - 18 male thread upstreamStandard 9/16" - 18 female downstream...

3 way 360 degree rotationStandard 9/16" - 18 thread 2nd stage regaulator to standard LP scuba 9/16" - 18 maleAccepts in-line quick disconnect...

Y Block Adaptor (MB-Z2) with 2 x 3/8" female (out)Inlet adaptor (SZM-YM) 9/16" male x 3/8" mal. This enables at 1st stage a 3/8" port to be split/extended into 2 ports....

OMS backpad and bookscrews. RRP £40...

COMPACT WEIGHT POCKET - This compact weight pouch (5" x 6") holds up to 5 lbs. of weight and can be mounted either vertically or horizontally....

OMS emergency deployment system. Can hold up to two smbs and the OMS depth canister. Does not include smbs or depth canister. RRP £54...

INTEGRATED WEIGHT POCKET - This optional add-on pocket system, combines an integrated weight system, utility pocket, a knife/shears pocket and fits on the waist webbing...

LARGE UTILITY POCKET. This large two pocket pouch is now expandable and will accommodate a redundant mask,jen line, tables, slate, etc.Each pocket contains a heavy duty nylon mounting loop for equipment attachment....

This integrated weight system consists of (2) matching pockets, incorporates No SagTM features, an inner pouch that holds the weight and is secured by a 2 Quick Release buckle to prevent accidental dumping of weights. Holds up to 15 lbs. Measures 9 L x 5.25 H. Material is rugged 1600 Denier Nylon....

SHEARS POUCH - Pouch to hold stainless steel shears, knife or line cutter: This pouch is designed to fit on 2" webbing and can be mounted in a horizontal or vertical fashion....

SMALL UTILITY POCKET. This is a more compact 2 pocket pouch version of the large pouch and has been redesigned with an expandable feature. Each pocket contains an equipment loop....

Personal filter and cartridge assembly. Idea for those trips away when you're unsure whether the air station is giving you clean air. A must for all Nitrox divers RRP £120...

Personal filter cartridge for the Verwood Undersea persanl filter RRP £23.50...

This carries multiple accessories: reel, writing slate, extra mask, compass etc. and can be mounted on Harness Advanced anywhere there is a 40cc- SystemT. Easy accessibility for awkwardly-placed pockets is enhanced by the TwistLockT attachment system. It's easy to operate wearing gloves, has a mesh ...

Material: Nylon Width: 25,4 mm (1 inch) Tow ring included: Yes...

The 40cc-SystemT Stainless steel D-ring is approved for 2000 N. and large numbers can be mounted in a variety of positions; there are 60 40cc-SystemT holes which can be used horizontally and vertically....

Poseidon Besea tank cam band...

The Pinbolt kit "Butterfly" is used for mounting twin cylinders onto the BESEA. The kit can be fitted on both Advanced or Sport harness and the stainless steel backplate. This kit is constructed to fit all twin cylinders....

Adaptors suitable for newer models of Poseidon Jetstream and Xstream regulators, which can be fitted to the standard 9/16" F end of a Miflex Xtreme hose.Please note that Poseidon have confirmed that these adaptors may not be suitable for older models of Jetstream regulators....

The Quick Mounting and Release (QMR) system is an ideal way of attaching twin or single cylinders fast. It´s much less cumbersome than ordinary bands, and has the added benefit of positioning cylinders in exactly the same position, dive after dive, thus maintaining underwater balance between dives. ...

The weight pocket QR - up to four on a waistband - feature the PocketRetractT system and are attached using the SprintReleaseT system (see following pages). All attached pockets can be dumped wherever they are placed and in any position you are in. No up or down. The EasyGripT handles are designed f...

The Quick Mounting and Release (QMR) system is an ideal way of attaching twin or single cylinders fast. It´s much less cumbersome than ordinary bands, and has the added benefit of positioning cylinders in exactly the same position, dive after dive, thus maintaining underwater balance between dives. ...

The metal back plate works with any BeSea bladder. It´s made in AISI 316 and can be connected as a support system to the BeSea harness for carrying multiple tanks and heavy equipment. The BESEA Continuous Loop and BESEA Semi Continous Loop can be used in place of a BESEA harness....

Quick Detach Twist Webbing Loop...

These dust caps are made to fit any standard 2nd (9/16") stage hose and reg fitting. One use is to cap the oxygen solenoid and hose of your rebreather or cap the ends of the ADV hoseIt fits the kiss BOV, or can be used simply to protect and keep hoses clean.They come as a set 1 male and 1 female (on...

Original rubber replacement strap for Jet Fins....

Spare or replacement clear crystal silicone, long lasting mask strap to fit most makes of mask. RRP £4.50...

Small computer wrist slate RRP £10...

Small Lanyard ...

SMB Reel Lanyard...

Flexible loop for attaching your snorkel to your mask. Simple, and effective...

Replacement boltkits for stainless steel bands. Made from marine grade 316 stainless steel 8mm fittings. RRP £8...

Detachable coiled lanyard with stainless clip...

Stainless steel 316 grade weight belt buckle. RRP £5.50...

1/4"Fem -B/Nose Fem Adaptor...

1/4 BSP Male to 3/8 UNF Male...

1/4 BSP Male-1/8 BSP Male Adaptor...

1/4 BSP Male-7/16 UNF Male...

1/4 NPT Blanking Plug...

Usefull panel mount female DIN for safe- clean "docking" of male DIN charging whips or panel mount H.P outlet ( 232bar )....

232 Bar Male Din-M16x1.5mm With Flow Stop...

3/8 UNF Male to 1/4 BSP Female ...

3/8 UNF Male-9/16 UNF LP Hose fitting...

300 Din Female- 300 Din Female...

50 Pack Spares Kit O Rings...

Adaptor 1/2 Unf Fem - 3/8 Unf Ml...

Adaptor 1/2 Unf Ml - 3/8 Unf Fem...

Adaptor 1/4 BSP Female-7/16 UNF Male...

A usefull fitting for L.P. connection to D.V. swivel hose ends such as inflation devices , air powered tools etc...

Adaptor 3/8 Unf Ml-1/8 Bsp Posiedon Fem...

Adaptor 7/16 Ml-3/8 Unf Fem...

Adaptor 7/16 Unf Fem - 3/8 Unf Ml...

Adaptor 7/16 Unf Fem - 7/16 Unf Ml...

Converts 1/4"BSP gauges to 1/4" BSP male to fit all of our fittings....

Adaptor Brass 1/4m X 1/4m Bsp...

Blank Plug 1/4" Bsp Male...

Blank Plug X 1/2 Unf...

Blank Plug X 1/8 Bsp...

Blank Plug X 3/8 Unf...

Blank Plug X 7/16 Unf...

Bleed Screw...

Enables 'A' Yoke charging of male threaded AB cylinders....

Bullnose Adaptor -European Configuration...

For bank coupling of storage cylinders 5/8"BSP - 350 bar w.p....

Bullnose Charging Adaptor With Bleed...

Charging Adaptor with bleed & Gauge...

Charging connection for Int yoke fitting pillar valved cylinders....

Din 232 Male To 2x Din 232 Female...

Din 232 Male-G1/4 Male With Green Handwheel...

Din 300 Male-16x1.5mm With Flow Stop...

With Green Handwheel and Oxygen Clean. Chromed Brass with G 1/4 Male thread & 60 cone seat....

Din Adaptor To 1/4 Bsp Ml (232 Bar)...

DIN 300 Male connection to G 1/4 Male x 60 cone....

Protects external threads of DIN regulators and fittings from damage and ingress of debris...

Protects valve and threads from the ingress of dust & debris....

Charging connection for 300 bar DIN configuration valved cylinders....

Charging connection for 232 bar DIN Cylinders....

Din Charging Adaptor With Gauge (232bar)...

300Bar charging adaptor with 400Bar guage to G 1/4...

Dual purpose fitting enabling thread protection of fem 232 bar DIN connections and high pressure blanking of fem DIN service ports - hence the fitted decompression bleed. ...

232 Bar DIN - Int block fitting - max service pressure 250 Bar. 300 Bar male is illegal....

Female 232 Din-Female 232 Din...

Female 232 Din-Female 300 Din...

Female Din ( 232 bar ) To 1/4 Bsp Female...

Female DIN ( 300 bar ) to 1/4" BSP female...

Female Euro Bullnose To 1/4 BSP Female...

Female Euro Bullnose to G 1/4 Female...

G 3/8 Male to G 1/4 Male in 316 Stainless Steel ...

Int Block & Seat ( For European Din Adaptor)...

Converts male 232 bar DIN to Int yoke charging outlet....

Male M26 - 1/4" Bsp male cone enabling charging NEW Euro Nitrox cylinder valves....

M26 Female To Male 300 Din...

Enables conversion of new euro spec nitrox regulators to be fitted to std DIN valves....

Enables conversion of new euro spec nitrox valves to existing regulators....

Enables filling of 232 Bar DIN cylinders from 300 Bar filling outlet....

Male 300 Din To Female 232 Din...

Din 232 Female to Male G 5/8...

Din 300 Female to Male G5/8 U.K. Bullnose to BS 341 type 3...

Nevoc W30 x2 Adaptor...

O Rings (10 Pack) 2.62mm X 11mm...

O Rings 2.62mm x 17mm (Bulk Qty 1000)...

O Rings 2.62mm x 18.72mm (Bulk Qty 1000)...

O Rings 2.62mm x 23.5mm (Bulk Qty 1000)...

Specifically for Oxygen enriched equipment applications....

BSP Female for panel mounting....

Gives an outlet flow rate of 2 Litres per minute. Used for analysing gases. All chrome plated brass construction. Regret not available for 300 Bar....

International yoke fitting - 1/4" bsp male cone....

Tee Bolt (For Charging Clamps M10 Thread)...

Not suitable for 'Air Products' or 'Air Liquide/Linde' cylinders...

U.K. Bullnose Adaptor To G1/4 Male Green Handwheel...

for storage cylinder connection 5/8" BSP with O ring seal on the bullnose - 350 bar w.p....

UK Bullnose To 1/4 NPT Male Thread...

W30 x 2 Nevoc to ISO 5145 Type 31 for Air...

W30 x 2 Nevoc to ISO 5145 Type 32 for Oxygen...

UK converter adaptor for O2 connection as used on "Mares Azimuth " rebreather system and other continental Oxygen medical cylinders ( Uni4406)       Weight: 0.2050kg...

Personal filter kit including a cartridge and an assortment of common filling adaptors. Nice presented in its own transit case...

Din dust cap for regulators. Helps protect against debris intrusion...

FITS ROUND DIVERS NECK AND USES LOOP TO KEEP 2 REGULATORS CLOSE TO THE FACE. NEGATIVE BUOYANCY ENSURES THAT THE REGS WILL NOT FLOAT IN FRONT OF THE FACE....

FITS ROUND DIVERS NECK AND USES LOOP TO KEEP REGULATOR CLOSE TO THE FACE. NEGATIVE BUOYANCY ENSURES THAT THE REG WILL NOT FLOAT IN FRONT OF THE FACE...

Super Detach Lanyard...

Torch Lanyard Number 1 snap hook on webbing with 7 1/2" cord loop ...

WaterBuoyWaterbuoy is the worlds first and strongest intelligent miniture flotation device visible at night. The waterbuoy has a number of applications, being able to attach to literally anything, including, keys, gps units, cameras, PDA's, Mobile phones, radio receives, fishing tackle, portable rad...

Weight Belt Security Lanyard Never lose your weight belt with this lanyard. Attach to the weight belt via the heavy duty, stainless steel three bar slide. 221/2” in length with heavy duty adjustable fastex buckle and No 2 snaphook ...

Gives up to five writing surfaces on the wrist RRP £16...

Wrist Lanyards - Extended Cord - Split Ring ...

Convert any standard regulator hose to a low pressure "EZ" QD hose Installs to the second stage end of a regulator hose Just push to attach - no need to pull back the collar Wide easy grip collar Chromed brass construction  Oxygen clean with Viton o-rings ...

Make any primary regulator more comfortable while diving Routes the hose under the right arm instead of over the shoulder Installs between the second stage and the regulator hose Chromed brass construction Oxygen clean with Viton o-ringsChrome plated brass constructionOxygen cleaned with Viton o...

Deep bellowed pocket with Velcro closure Stainless steel side grommets on side and bottomInterior mesh divider (2) D-rings and (1) snap clip inside pocket Three Ways of Attachment - Slide it over 2" webbing - Slide it over 4" cummerbund - Clip it on your BC w/2 built-in snap clipsSize: 17cm wide x ...

Enable your Miflex inflator hose to be easier to operate to use when wearing gloves.This simple retro-fit Hose End / Top hat fits onto the standard hose fitting for easier use....

This adapter allows connection of a 3/8" low pressure regulator hose into a 1/2" regulator first stage low pressure port Black-chromed brass construction Oxygen clean with Viton o-ring ...

9/16" M x 3/8" F adaptor to extend the length of regulator hoses by joining 2 togetherBlack-chromed brass construction ...

A first stage LP Port Extender with 3/8" Male x 3/8" Female UNF connections....

Heavy-Duty PVC Coated Nylon MeshVelcro ClosureSix Stainless Steel Grommets for AttachmentDimension 6.5" x 12"...

Accessory pocket with zipper closure Perfect for small lights, slates, or gloves D-ring and snap clip inside pocket Three Ways of Attachment - Slide it over 2" webbing - Slide it over 4" cummerbund - Clip it on your BC w/2 built-in snap clips Size: 15cm wide x 21cm high...

Convert any standard regulator hose to a Oceanic Style" QD hose Installs to the second stage end of a regulator hose Chromed brass construction Oxygen clean with Viton o-rings Compatible with:- Oceanic Air XS- Aeris Air Link- Zeagle Octo Plus- Beauchat Venturi...

Convert any standard regulator hose to a "ScubaPro Style" QD hose Installs to the second stage end of a regulator hose Chromed brass construction Oxygen clean with Viton o-rings Compatible with:- Tusa Duo Air- ScubaPro Air 2- Atomic SS1 - Sherwood Gemini...

Convert any standard regulator hose to a "SeaQuest Style" QD hose Installs to the second stage end of a regulator hose Chromed brass construction Oxygen clean with Viton o-rings Compatible with:- SeaQuest Air Source- US Divers Air Mic ...

Small utility pocket with Velcro closure Stainless steel gromments on side and bottom D-ring and snap clip inside pocket Three Ways Of Attachment - Slide it over 2" webbing - Slide it over 4" cummerbund - Clip it on your BC w/2 built-in snap clipsSize: 18cm wide x 18cm high...